Manufacturing solutions built for clean-energy projects.
Solar components for every part of the plant
Modules, trackers, structures, foundations and BOS hardware for solar plants.
Modules, Cells & Components
- Mono PERC & TOPCon modules
- Solar cells & wafers
- Glass, encapsulant films & backsheet
- Aluminium frames, junction boxes & connectors
Tracker Components
- Torque tubes
- Bearing housings & post heads
- Slew-drive & damper brackets
- Driveline shafts & couplers
Module Mounting Structures
- Fixed-tilt & seasonal-tilt structures
- Rooftop & elevated walkable structures
- Solar carports
- Purlins, rafters, columns & clamps
Foundations & Piles
- Driven piles (W & C sections)
- Ground screws
- Pile caps & adaptors
- Pre-cast anchor assemblies
Balance of System & Site Works
- Cable trays, ladders & earthing
- Combiner, ACDB & DCDB enclosures
- Perimeter fencing & gates
- Module cleaning platforms & walkways
Evacuation & Transmission
- Transmission line towers
- Substation gantries & equipment supports
- Inverter & transformer platforms
- ACSR / AAAC conductors and OPGW
Wind components from foundation to nacelle
Tower, flange, bolting, foundation and nacelle parts for turbine OEMs and wind EPCs.
Tower Sections & Shells
- Rolled & welded tower cans
- Door frames & reinforcements
- Section assemblies
- Internal coating & painting
Flanges & Connections
- Ring flanges, machined
- Bolted section joints
- Flange facing & flatness control
- Weld preparation & fit-up
Fasteners & Bolting Kits
- HV bolt sets, M36–M56, 10.9 / 12.9
- Nuts, washers & coatings
- Kitted per flange joint
- Replacement sets for O&M
Tower Internals
- Platforms & gratings
- Ladders & fall-arrest rails
- Cable trays & clamps
- Lift support steel
Foundation & Anchor Systems
- Anchor cages
- Anchor bolts & templates
- Embedment rings
- Levelling & support frames
Nacelle, Hub & Drivetrain Parts
- Nacelle frame fabrications & bedplates
- Machined hub castings
- Yaw & pitch ring machining
- Service platforms & covers
Hydrogen components from stack to storage
Skids, vessels, stack hardware and piping for electrolyser OEMs and hydrogen developers.
Electrolyser Skids & Module Frames
- Module base & lifting frames
- Process skid frames
- Circulation & purification skids
- Series builds to frozen drawings
Separators & Process Vessels
- Gas-liquid separators
- Lye & water buffer drums
- Wash towers & scrubbers
- H₂S and dryer vessels
Storage, Cascades & Refuelling
- Buffer & storage vessels
- Cylinder cascades, racks & cradles
- Compressor & chiller skid frames
- Dispenser housings & canopies
Stack Components
- End & compression plates
- Tie rods & compression hardware
- Current collectors & busbars
- Stack frames
Plant Structures & Enclosures
- Container enclosures & acoustic hoods
- Pipe racks
- Platforms & access structures
- Vent stack supports
Piping Spools & Manifolds
- SS 316L process spools
- Utility & cooling piping
- Manifolds & valve stations
- PMI, radiography & leak testing
Biogas components from feedstock to CBG
Tanks, feedstock handling, upgrading skids and plant steel for biogas and CBG plants.
Digester & Tank Steelwork
- Digester & hydrolysis tank shells
- Roof frames, covers & gas-holder ring beams
- Agitator bridges & mounts
- Manways, nozzles & cladding
Feedstock Handling & Pre-treatment
- Feed hoppers, silos & chutes
- Screw conveyors & augers
- Belt conveyor structures
- Shredder, press & mixing frames
Gas Upgrading & CBG Skids
- PSA, membrane & water-scrubbing skids
- Upgrading & scrubbing column shells
- H₂S removal vessels
- Pipe spools, chillers & dryer skids
Compression, Bottling & Cascades
- Compressor skid frames & bases
- Cascade cylinder racks & cradles
- Bottling shed structures
- Dispenser canopies & LCV loading platforms
Digestate Handling & Separation
- Decanter & screw-press frames
- Separator & drying structures
- Digestate tanks & lagoon steelwork
- FOM handling & bagging structures
Plant Structures & Utilities
- Pipe racks, platforms & stairs
- Flare stack structures
- Control room, MCC & PEB buildings
- Utility, boiler & water-treatment skids
Clean-energy components, built to your drawings
Custom parts for EV charging, small hydro and waste-to-energy projects.
EV Charging Infrastructure
- Charging canopies
- Charger enclosures & pedestals
- Cable management
- Signage frames
Small Hydro
- Penstock supports
- Trash racks
- Gate frames
- Powerhouse steel
Waste-to-Energy
- Conveyor & chute structures
- Boiler platforms & stairs
- Duct supports
- Equipment frames
Need something that isn’t listed? We also make custom clean-energy parts and assemblies to your drawings.
- 250–355 MPa: Structural Steel Yield Strength
- M36–M56: Wind Tower Bolting Kits
- SS 316L: Hydrogen Process Piping
What ManuFx brings to every renewable energy project
- Engineering at every stage. Drawing review, manufacturability checks and inspection, from quote to dispatch.
- Vertically integrated supply chain. Steel, fabrication, galvanizing and finishing planned as one supply chain.
- 25+ clusters, 100k+ vendors. Manufacturing capacity matched to each part, volume and delivery date.
- Backed by HOJ. 66 years of industrial legacy and 4+ integrated clean-energy verticals behind every project.
Certifications and standards
- ISO 9001 ISO 9001
- ISO 14001 ISO 14001
- ISO 45001 ISO 45001
- ISO 3834 ISO 3834
- Bureau of Indian Standards
- American Institute of Steel Construction
Why renewable energy teams choose ManuFx
One partner for clean-energy components, from drawing to delivery.
- Faster Project Execution. One execution plan for fabrication, finishing and logistics
- Built to Your Specification. Made to project specs, traceable from material to finish
- Quality at Every Stage. Stage inspections, test reports and third-party checks
Applications across clean energy
- Solar & PV Infrastructure
- Wind Energy Systems
- Bioenergy & Biogas
- Battery & Energy Storage
- Hydrogen & Electrolyser Systems
- Hydropower & Other Renewables
Processes, materials and finishes
Materials: E250 Structural Steel, E350 Structural Steel, S355 Structural Steel, 304 Stainless Steel, A36 Carbon Steel, 316L Stainless Steel, Pre-Galvanized (GI) Steel, 6005-T5 Aluminium, 6063-T6 Aluminium, 6061-T6 Aluminium, Duplex Coating (Galvanizing + Paint), Zinc Metallizing, Zinc-Magnesium-Aluminium Coated Steel, Structural Hollow Sections, High-Strength Bolts & Fasteners.
Processes: CNC Machining, Pressure Vessel Fabrication, Roll Forming & Punching, Tube & Pipe Processing, Plate Rolling & Welding, Structural Fabrication, Pipe Spool Fabrication, Skid Assembly & Integration, Assembly & Kitting, Blasting & Painting.
Finishes: Hot-Dip Galvanizing, Near-White Blast Cleaning, Epoxy / PU Paint Systems, Duplex Coating (Galvanizing + Paint), Zinc Metallizing, Powder Coating, Anodizing, Pickling & Passivation, Electropolishing, Zinc-Flake Coating, Zinc Plating, Nickel Plating.
Other industries we serve
Planning a renewable energy project?
Send your drawings and requirements. We’ll quote, manufacture and deliver to your specification.